to fit x1 headlamp

contains three sets of shim thicknesses; thin medium and thick. instructions included.

remanufactured from aluminium and stainless steel as improved replacements for the originals. each kit includes one complete short latch and one complete long latch, rubber seals, stainless detent plungers and the circular external finisher trims.

runs front to rear along top of engine valley

for 2 piece early doors and ex-military doors with sliding glass.

for 2 piece early doors and ex-military doors with sliding glass.

for 2 piece early doors and ex-military doors with sliding glass.

for 2 piece early doors and ex-military doors with sliding glass.

to fit x1 headlamp

mounts into any Carling Contura switch aperture. charges at the faster speed required by the latest Apple devices. internal filtering for reduced electronic interference. over temperature protection. protective dust cap keeps debris and moisture out. conformal coated circuit board for harsh off-road environments. highest quality Blue Sea brand. input voltage range 9-32V DC. parasitic current draw 1mA. maximum output current 4.8A DC (total).

order with a rocker facia to make a complete switch. Standard on-off switch. Green/Orange LED illumination NB: can also be used as an On-On switch (typically used to switch between a work light with reverse/manual operation). • Universal Style (can be fitted with both US & EU Style switches). • Single Pole switch. • V-Series switches are rated at 12v, 20amps. • Wired with standard 6.3mm spade terminals to the rear of the switches. Pair with the laser etched Contura V rockers or the Contura II, Contura XIV to create a complete switch.

individual interlocking switch frames allow you to create your own multiple gang mounts . order with end mounts FF014217. accepts Contura V rocker switches.

individual interlocking switch frames allow you to create your own multiple gang mounts. order with centre mounts FF014216. order two of these frame ends for all installations. e.g. to install seven switches, order 5 x centres and 2 x ends. to mount only two switches side-by-side, use 2x interlocking ends. accepts Contura V rocker switches.

accepts Contura V rocker switches.

accepts Contura V rocker switches.

not an actual switch. a neat and tidy way to fill unused holes in any Carling switch mount.

eliminate moisture ingress between mounting surface and the rear of switch. order one seal per switch.

dedicated multiplug for the Carling technologies hazard switch. coloured red for easy identification. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

tidy up a multiple switch installation with this dedicated Carling multi-plug connector block. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

contains three sets of shim thicknesses; thin medium and thick. instructions included.

Reconditioned units - may have imperfections. Complete with O Ring.

O Ring for Oil Filler Cap FF011382

Terrafirma performance brake upgrade kits include huge 6 piston front calipers, EBC Redstuff brake pads with increased surface area and extra-large 330x32mm vented and grooved front brake discs, larger 4 piston rear calipers, also with EBC Redstuff brake pads. The brake kit fits within alloy or steel 16 inch or larger wheels, improving braking performance and reducing stopping distances considerably whilst adding a touch of style to your Defender. hard anodised and ceramic coated for appearance and durability, produced from aerospace grade aluminium for strength. Stainless Steel pistons and pins. Highest grade seals and O rings. Superior Holokrome 12.9 grade hi-tensile bolts. EBC Redstuff brake pads Large Diameter vented and grooved front brake discs. Full traceability of all manufactured parts. Extensive laboratory and track testing to prove safety and performance. Suitable for models with or without ABS NB: The Terrafirma performance brake upgrade kits are designed to fit with the original rear brake discs LR018026 or LR017951 which are 298mm diameter. If your vehicle is fitted with very early 290mm rear brake discs you will have to replace them with 298mm diameter discs (not included in this kit).

Terrafirma performance brake upgrade kits include huge 6 piston front calipers, EBC Redstuff brake pads with increased surface area and extra-large 330x32mm vented and grooved front brake discs, larger 4 piston rear calipers, also with EBC Redstuff brake pads. The brake kit fits within alloy or steel 16 inch or larger wheels, improving braking performance and reducing stopping distances considerably whilst adding a touch of style to your Defender. hard anodised and ceramic coated for appearance and durability, produced from aerospace grade aluminium for strength. Stainless Steel pistons and pins. Highest grade seals and O rings. Superior Holokrome 12.9 grade hi-tensile bolts. EBC Redstuff brake pads Large Diameter vented and grooved front brake discs. Full traceability of all manufactured parts. Extensive laboratory and track testing to prove safety and performance. Suitable for models with or without ABS NB: The Terrafirma performance brake upgrade kits are designed to fit with the original rear brake discs LR018026 or LR017951 which are 298mm diameter. If your vehicle is fitted with very early 290mm rear brake discs you will have to replace them with 298mm diameter discs (not included in this kit).

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

these colour co-ordinated blanking plates for the rear door fit in place of the original spare wheel brackets, allowing you to remove the spare wheel and bracketry and replace with snug fit blanking plates for a smart flush finish. easy to install 2-piece kit supplied with all necessary fixings.

runs front to rear along top of engine valley

6.25 inches x 0.75 inches. for tying two pipes together

mounts into any Carling Contura switch aperture. charges at the faster speed required by the latest Apple devices. internal filtering for reduced electronic interference. over temperature protection. protective dust cap keeps debris and moisture out. conformal coated circuit board for harsh off-road environments. highest quality Blue Sea brand. input voltage range 9-32V DC. parasitic current draw 1mA. maximum output current 4.8A DC (total).

order with a rocker facia to make a complete switch. Standard on-off switch. Green/Orange LED illumination NB: can also be used as an On-On switch (typically used to switch between a work light with reverse/manual operation). • Universal Style (can be fitted with both US & EU Style switches). • Single Pole switch. • V-Series switches are rated at 12v, 20amps. • Wired with standard 6.3mm spade terminals to the rear of the switches. Pair with the laser etched Contura V rockers or the Contura II, Contura XIV to create a complete switch.

individual interlocking switch frames allow you to create your own multiple gang mounts . order with end mounts FF014217. accepts Contura V rocker switches.

individual interlocking switch frames allow you to create your own multiple gang mounts. order with centre mounts FF014216. order two of these frame ends for all installations. e.g. to install seven switches, order 5 x centres and 2 x ends. to mount only two switches side-by-side, use 2x interlocking ends. accepts Contura V rocker switches.

accepts Contura V rocker switches.

accepts Contura V rocker switches.

not an actual switch. a neat and tidy way to fill unused holes in any Carling switch mount.

eliminate moisture ingress between mounting surface and the rear of switch. order one seal per switch.

dedicated multiplug for the Carling technologies hazard switch. coloured red for easy identification. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

tidy up a multiple switch installation with this dedicated Carling multi-plug connector block. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

contains three sets of shim thicknesses; thin medium and thick. instructions included.

Reconditioned units - may have imperfections. Complete with O Ring.

O Ring for Oil Filler Cap FF011382

mounts into any Carling Contura switch aperture. charges at the faster speed required by the latest Apple devices. internal filtering for reduced electronic interference. over temperature protection. protective dust cap keeps debris and moisture out. conformal coated circuit board for harsh off-road environments. highest quality Blue Sea brand. input voltage range 9-32V DC. parasitic current draw 1mA. maximum output current 4.8A DC (total).

order with a rocker facia to make a complete switch. Standard on-off switch. Green/Orange LED illumination NB: can also be used as an On-On switch (typically used to switch between a work light with reverse/manual operation). • Universal Style (can be fitted with both US & EU Style switches). • Single Pole switch. • V-Series switches are rated at 12v, 20amps. • Wired with standard 6.3mm spade terminals to the rear of the switches. Pair with the laser etched Contura V rockers or the Contura II, Contura XIV to create a complete switch.

individual interlocking switch frames allow you to create your own multiple gang mounts . order with end mounts FF014217. accepts Contura V rocker switches.

individual interlocking switch frames allow you to create your own multiple gang mounts. order with centre mounts FF014216. order two of these frame ends for all installations. e.g. to install seven switches, order 5 x centres and 2 x ends. to mount only two switches side-by-side, use 2x interlocking ends. accepts Contura V rocker switches.

accepts Contura V rocker switches.

accepts Contura V rocker switches.

not an actual switch. a neat and tidy way to fill unused holes in any Carling switch mount.

eliminate moisture ingress between mounting surface and the rear of switch. order one seal per switch.

dedicated multiplug for the Carling technologies hazard switch. coloured red for easy identification. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

tidy up a multiple switch installation with this dedicated Carling multi-plug connector block. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

contains three sets of shim thicknesses; thin medium and thick. instructions included.

Reconditioned units - may have imperfections. Complete with O Ring.

O Ring for Oil Filler Cap FF011382

mounts into any Carling Contura switch aperture. charges at the faster speed required by the latest Apple devices. internal filtering for reduced electronic interference. over temperature protection. protective dust cap keeps debris and moisture out. conformal coated circuit board for harsh off-road environments. highest quality Blue Sea brand. input voltage range 9-32V DC. parasitic current draw 1mA. maximum output current 4.8A DC (total).

order with a rocker facia to make a complete switch. Standard on-off switch. Green/Orange LED illumination NB: can also be used as an On-On switch (typically used to switch between a work light with reverse/manual operation). • Universal Style (can be fitted with both US & EU Style switches). • Single Pole switch. • V-Series switches are rated at 12v, 20amps. • Wired with standard 6.3mm spade terminals to the rear of the switches. Pair with the laser etched Contura V rockers or the Contura II, Contura XIV to create a complete switch.

individual interlocking switch frames allow you to create your own multiple gang mounts . order with end mounts FF014217. accepts Contura V rocker switches.

individual interlocking switch frames allow you to create your own multiple gang mounts. order with centre mounts FF014216. order two of these frame ends for all installations. e.g. to install seven switches, order 5 x centres and 2 x ends. to mount only two switches side-by-side, use 2x interlocking ends. accepts Contura V rocker switches.

accepts Contura V rocker switches.

accepts Contura V rocker switches.

not an actual switch. a neat and tidy way to fill unused holes in any Carling switch mount.

eliminate moisture ingress between mounting surface and the rear of switch. order one seal per switch.

dedicated multiplug for the Carling technologies hazard switch. coloured red for easy identification. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

tidy up a multiple switch installation with this dedicated Carling multi-plug connector block. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

contains three sets of shim thicknesses; thin medium and thick. instructions included.

The EAS (Electronic Air Suspension) System originally fitted to Land Rover vehicles can present expensive, recurring maintenance problems. This coil spring conversion kit for the Discovery 3/4 and Range Rover Sport (2005-2013 non ACE) models makes switching to coil springs seamless and error-free. Conversion to coil springs provides a maintenance-free ride that will save you significant money over time. The EAS Override Module suppresses all typical false dashboard display errors and buzzers seen when converting to coil springs. Any mechanic can install this coil spring conversion kit without having to visit a franchised Land Rover dealer or Autologic-equipped workshop to eliminate false dash warning light errors. Trip computer compatibility - maintains operation of your vehicles trip computer. Kit provides everything needed to complete a professional installation. Fit this coil spring conversion kit in place of the standard air suspension. - Disables the air suspension control unit - Does not disturb the other control systems of the vehicle - No compromise to vehicle ride quality - easy to fit - Low Maintenance We advise that you inform your vehicle insurance company of this modification before fitment.

includes end nut with the correct 2.0mm thread pitch

When replacing the front timing belt kit on all TDV6 engines we strongly recommend that the oil pump FF015094 and seals FF007646 x2 are replaced. Failure to do so could result in premature engine failure.

The EAS (Electronic Air Suspension) System originally fitted to Land Rover vehicles can present expensive, recurring maintenance problems. This coil spring conversion kit for the Discovery 3/4 and Range Rover Sport (2005-2013 non ACE) models makes switching to coil springs seamless and error-free. Conversion to coil springs provides a maintenance-free ride that will save you significant money over time. The EAS Override Module suppresses all typical false dashboard display errors and buzzers seen when converting to coil springs. Any mechanic can install this coil spring conversion kit without having to visit a franchised Land Rover dealer or Autologic-equipped workshop to eliminate false dash warning light errors. Trip computer compatibility - maintains operation of your vehicles trip computer. Kit provides everything needed to complete a professional installation. Fit this coil spring conversion kit in place of the standard air suspension. - Disables the air suspension control unit - Does not disturb the other control systems of the vehicle - No compromise to vehicle ride quality - easy to fit - Low Maintenance We advise that you inform your vehicle insurance company of this modification before fitment.

includes end nut with the correct 2.0mm thread pitch

When replacing the front timing belt kit on all TDV6 engines we strongly recommend that the oil pump FF015094 and seals FF007646 x2 are replaced. Failure to do so could result in premature engine failure.

order with plinth FF011360.

runs front to rear along top of engine valley

includes seal between glass and frame. glass and fixings NOT supplied - re use your existing parts. supplied in bare metal - will need to be painted before fitment.

includes seal between glass and frame. glass and fixings NOT supplied - re use your existing parts. supplied in bare metal - will need to be painted before fitment.

screws not included. order with FF002563 gaiter

aluminium

zinc plated

zinc plated

a close copy of the long since obsolete original gearbox tunnel cover for the early vehicles.

a close copy of the long since obsolete original gearbox tunnel cover for the early vehicles.

2 screws and washers supplied in kit.

6.25 inches x 0.75 inches. for tying two pipes together

remanufactured by Famous Four. identical to the original soft rubber buffer. 2 required per vehicle.

ABS plastic

to fit x1 headlamp

not handed - fits both left and right side of vehicle.

Palamino coloured thermo-plastic elastomer. Suitable for either right or left hand drive vehicles - Markings on the back of the mats show where to trim the small section for the steering column.

Palamino coloured thermo-plastic elastomer. Designed to fit directly onto the floor pan so any carpet or insulation material will need to be removed before installing. Lower B pillar trims will have to be removed and refitted as these sit over the top of the mat to hold it in place.

Palamino coloured thermo-plastic elastomer. Suitable for either right or left hand drive vehicles - Markings on the back of the front row mats show where to trim the small section for the steering column. Second row mat is designed to fit directly onto the floor pan so any carpet or insulation material will need to be removed before installing. Lower B pillar trims will have to be removed and refitted as these sit over the top of the mat to hold it in place.

sold in a pack of 20

mounts into any Carling Contura switch aperture. charges at the faster speed required by the latest Apple devices. internal filtering for reduced electronic interference. over temperature protection. protective dust cap keeps debris and moisture out. conformal coated circuit board for harsh off-road environments. highest quality Blue Sea brand. input voltage range 9-32V DC. parasitic current draw 1mA. maximum output current 4.8A DC (total).

order with a rocker facia to make a complete switch. Standard on-off switch. Green/Orange LED illumination NB: can also be used as an On-On switch (typically used to switch between a work light with reverse/manual operation). • Universal Style (can be fitted with both US & EU Style switches). • Single Pole switch. • V-Series switches are rated at 12v, 20amps. • Wired with standard 6.3mm spade terminals to the rear of the switches. Pair with the laser etched Contura V rockers or the Contura II, Contura XIV to create a complete switch.

individual interlocking switch frames allow you to create your own multiple gang mounts . order with end mounts FF014217. accepts Contura V rocker switches.

individual interlocking switch frames allow you to create your own multiple gang mounts. order with centre mounts FF014216. order two of these frame ends for all installations. e.g. to install seven switches, order 5 x centres and 2 x ends. to mount only two switches side-by-side, use 2x interlocking ends. accepts Contura V rocker switches.

accepts Contura V rocker switches.

accepts Contura V rocker switches.

not an actual switch. a neat and tidy way to fill unused holes in any Carling switch mount.

eliminate moisture ingress between mounting surface and the rear of switch. order one seal per switch.

dedicated multiplug for the Carling technologies hazard switch. coloured red for easy identification. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

tidy up a multiple switch installation with this dedicated Carling multi-plug connector block. plugs into back of Carling switch body. locking tab offers a secure connection. requires 6.3mm female latching spade terminals. NB. the total depth required for a switch and connector is 50mm - check available clearance. NB. due to the different pin configurations the standard black switch multiplugs are not compatible with the Carling hazard warning switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

order with a rocker switch body (e.g. FF014215) to make a complete switch. this laser etched Carling Contura V rocker is compatible with all V-Series & J-Series Carling switch bodies. supplied in black plastic finish. update your old Carling J series switch rockers without having to buy new switches. NB this listing is for the Carling Contura V rocker/actuator and does not include the switch body. If you do not already have switch bodies you will need to add them to the rocker to create a complete switch.

contains three sets of shim thicknesses; thin medium and thick. instructions included.

for 3/16 diameter washer pipe. 5mm inlet and two 3mm outlets

weld in to door top frame. designed to repair the rearmost vertical channel section into which the quarterlight seal fits, which commonly corrodes. suitable for either left or right hand side front doors. 1 required for each door.

Reconditioned units - may have imperfections. Complete with O Ring.

O Ring for Oil Filler Cap FF011382

plastic. 3 required per vehicle

plastic. includes 3 vents. trim finishers are not included

kit includes 3 scuttle vents and 4 grille trim finishers.

runs front to rear along top of engine valley

fits between FF003811 and the outer wing.

includes seal between glass and frame. glass and fixings NOT supplied - re use your existing parts. supplied in bare metal - will need to be painted before fitment.

includes seal between glass and frame. glass and fixings NOT supplied - re use your existing parts. supplied in bare metal - will need to be painted before fitment.

birds eye maple veneered wood with chromed pivoting brackets. designed to be fitted to the rear of the front seats (drilling of the rear seat panel is necessary)

birds eye maple veneered wood with chromed pivoting brackets. designed to be fitted to the rear of the front seats (drilling of the rear seat panel is necessary)

aluminium

zinc plated

zinc plated

6.25 inches x 0.75 inches. for tying two pipes together